Effect Scenes
Space
Two kinds of Reverbs depending on FX knob position.
FX knob clockwise: Classic long-tail reverb with tone and filter control.
- FX sets the Reverb amount and a bit of High-Pass filter.
- CTRL sets the tone of the reverb.
- Hold the SPACE button until it’s fast blinking and turn the CTRL knob to adjust the amount of High-Pass filter.
FX knob counter-clockwise: Experimental reverb from shimmery to deep/black-hole textures.
- FX sets the reverb amount.
- CTRL sets the tone of the reverb.
Riser
Two kinds of Risers depending on FX knob position.
FX knob clockwise: high pass filter with reverb and noise build up.
- FX sets the Riser intensity.
- CTRL affects the filter resonance and amount of noise.
FX knob counter-clockwise: high pass filter with reverb and Shepard Tone style build up
- FX sets the Riser intensity.
- CTRL affects the filter resonance and amount of pitch riser and noise.
DJ Filter
A DJ style Filter with resonance control.
FX knob clockwise: high-pass filter.
FX knob counter-clockwise: low-pass filter.
- FX sets the filter frequency.
- CTRL sets the filter resonance. In High Pass mode, the resonance in the lower frequencies is decreased to avoid bass cluttering.
Loop / Beat-Repeat
A Looper and Reverse Looper / beat-repeat. Synced to tempo with a touch of High-Pass filter.
FX knob clockwise: forward looper.
FX knob counter-clockwise: reverse looper.
- FX engages the Looper and crossfades between the dry signal and the looper buffer. This control also engages the high-pass filter progressively.
- CTRL sets the looper division relative to the internal or external BPM.
- Hold the LOOP button until it’s fast blinking and turn the CTRL knob to adjust the amount of filter.
The Time Divisions are the following, from Counter Clockwise to Clockwise:
1/32, 1/16, 1/8, 1/4, 1/2, 1/1
Delay
A Clocked Delay with reverb wash and HP/LP Filter.
FX knob clockwise: delay with high pass filter.
FX knob counter-clockwise: delay with low-pass filter.
- FX sets the effect amount and the filter cutoff.
- CTRL sets the delay division relative to the internal or external BPM.
- Hold the DELAY button until it’s fast blinking and turn the CTRL knob to adjust the amount of filter.
The Time Divisions are the following, from Counter Clockwise to Clockwise:
1/32, 1/24, 1/16, 1/12, 1/8, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1/1, 4/3, 3/2, 2/1
Fully Counter-Clockwise, below 1/32, it’s fractions of 1/32 in milliseconds.
Gater
Two effects in one knob including:
FX knob clockwise: GATER with time division control and built-in High-Pass filter.
- FX sets the effect amount of effect and the filter cutoff.
- CTRL sets the Gater division relative to the internal or external BPM.
- Hold the GATER button until it’s fast blinking and turn the CTRL knob to adjust the amount of filter.
FX knob counter-clockwise: Snare-Roll build up with reverb and built-in High Pass filter
- FX sets the snare-roll and reverb amount and the filter cutoff.
- CTRL sets the snare-roll rate relative to the internal or external BPM.
- Hold the GATER button until it’s fast blinking and turn the CTRL knob to adjust the amount of filter.
The Time Divisions are the following, from Counter Clockwise to Clockwise:
1/32, 1/16, 1/8, 1/4, 1/2, 1/1